Exploring the Multifunctional Nature of Activated Carbon Filtration

Nov. 30, 2018

About the author:

Francis J. DeSilva has worked in the water treatment industry for more than 20 years. He is national sales manager for ResinTech, Inc., and currently is the director of the Water Treatment Section of the Liberty Bell Corrosion Course.

undefined

Granular activated carbon (GAC) is commonly used for removing organic constituents and residual disinfectants in water supplies. This not only improves taste and minimizes health hazards, it protects other water treatment units such as reverse osmosis membranes and ion exchange resins from possible damage due to oxidation or organic fouling. Activated carbon is a favored water treatment technique because of its multifunctional nature and the fact that it adds nothing detrimental to the treated water.

Most activated carbons are made from raw materials such as nut shells, wood, coal and petroleum.

Typical surface area for activated carbon is approximately 1,000 square meters per gram (m2/gm). However, different raw materials produce different types of activated carbon varying in hardness, density, pore and particle sizes, surface areas, extractables, ash and pH. These differences in properties make carbons often preferable over other methods in various applications.

The two principal mechanisms by which activated carbon removes contaminants from water are adsorption and catalytic reduction. Organics are removed by adsorption and residual disinfectants are removed by catalytic reduction. Factors that affect the performance of activated carbon are

  • Molecular weight. As the molecular weight increases, the activated carbon adsorbs more effectively because the molecules are less soluble in water. However, the pore structure of the carbon must be large enough to allow the molecules to migrate within. A mixture of high and low molecular weight molecules should be designed for the removal of the more difficult species.
  • pH. Most organics are less soluble and more readily adsorbed at a lower pH. As the pH increases, removal decreases. A rule of thumb is to increase the size of the carbon bed by 20 percent for every pH unit above neutral (7.0).
  • Contaminant concentration. The higher the contaminant concentration, the greater the removal capacity of activated carbon. The contaminant molecule is more likely to diffuse into a pore and become adsorbed. As concentrations increase, however, so do effluent leaks. The upper limit for contaminants is a few hundred parts per million. Higher contaminant concentration may require more contact time with the activated carbon. Also, the removal of organics is enhanced by the presence of hardness in the water, so whenever possible, place activated carbon units upstream of the ion removal units. This is usually the case anyway since activated carbon often is used upstream of ion exchange or membranes to remove chlorine.
  • Particle size. Activated carbon is commonly available in 8 ¥ 30 mesh (largest), 12 ¥ 40 mesh (most common) and 20 ¥ 50 mesh (finest). The finer mesh gives the best contact and better removal, but at the expense of higher pressure drop. A rule of thumb here is that the 8 ¥ 30 mesh gives two to three times better removal than the 12 ¥ 40, and 10 to 20 times better kinetic removal than the 20 ¥ 50 mesh.
  • Flow rate. Generally, the lower the flow rate, the more time the contaminant will have to diffuse into a pore and be adsorbed. Adsorption by activated carbon is almost always improved by a longer contact time. Again, in general terms, a carbon bed of 20 ¥ 50 mesh can be run at twice the flow rate of a bed of 12 ¥ 40 mesh, and a carbon bed of 12 ¥ 40 mesh can be run at twice the flow rate of a bed of 8 ¥ 30 mesh. Whenever considering higher flow rates with finer mesh carbons, watch for an increased pressure drop.
  • Temperature. Higher water temperatures decrease the solution viscosity and can increase the diffusion rate, thereby increasing adsorption. Higher temperatures also can disrupt the adsorptive bond and slightly decrease adsorption. It depends on the organic compound being removed, but generally, lower temperatures seem to favor adsorption.

Organic Removal

Organic material in public water supplies comes from decaying plant life, which becomes more soluble in water over time and exists as large, high-molecular weight organic acids (non-polar weak acids). Eventually, smaller molecular weight acids of varying sizes form. Typical organic acid molecules range in molecular weight from a few hundred to tens of thousands.

The size, number and chemical structure of organic acid molecules depend on a large number of factors including water pH and temperature. Accordingly, there exists an almost infinite number of organic acids. As a result, removing organics can be difficult and is always site-specific.

Activated carbon's adsorptive properties are used to remove organics. Generally, adsorption takes place because all molecules exert forces to adhere to each other. Activated carbon adsorbs organic material because the attractive forces between the carbon surface (non-polar) and the contaminant (non-polar) are stronger than the forces keeping the contaminant dissolved in water (polar).

The adsorptive forces are weak and cannot occur unless the organic molecules are close to the carbon's surface. The large surface area of the activated carbon, due to its particle size and pore configuration, allows for the adsorption to take place.Factors that decrease solubility and/or increase accessibility to the pores improve the performance of the activated carbon filter. Carbon filter capacity can be roughly estimated at 0.1 pound of organics per 1 pound of carbon at a flow rate of 1 to 2 gallons per minute per cubic foot (gpm/cu.ft.) and a bed depth of 3 feet.

Residual Disinfectants Removal

Activated carbon can remove and destroy residual disinfectants (chlorine and chloramine) through a catalytic reduction reaction. This is a chemical reaction that involves a transfer of electrons from the activated carbon surface to the residual disinfectant. In other words, activated carbon acts as a reducing agent.

Activated carbon's removal of chlorine reduces the chlorine to a non-oxidative chloride ion. The reaction is very fast and takes place in the first few inches of a new activated carbon bed. (Where removal of organics by activated carbon takes minutes, removal of chlorine literally takes seconds). The chlorine capacity of new activated carbon is 1 pound of chlorine per pound of carbon at a flow rate of 3 to 5 gpm/cu.ft. and a bed depth of 3 feet.

Chloramine removal by activated carbon is a much slower reaction. The predominant species of chloramine in city water supplies (pH about 7 to 8) is monochloramine. The reaction with activated carbon and monochloramine also renders a non-oxidative chloride ion. Since the rate of reaction is considerably slower, the flow rate should be 0.5 gpm/cu. ft. and the bed depth greater than 3 feet.

Material Considerations

Activated carbon beds are filters and need to be backwashed periodically. A freeboard of about 50 percent should be incorporated into the vessel design to allow backwash in place. Otherwise, external backwash is required. The backwash step does not "regenerate" the carbon or de-adsorb contaminants. The backwash step reclassifies the bed and removes any fines or suspended matter.

Carbon fines are generated during transport, handling and loading of activated carbon. These fines need to be backwashed out before service. Pre-wetted and backwashed carbons are available that minimize the fines and also eliminate the problems caused by carbon dust in a facility. Loading carbon tanks with dry carbon is a messy, hazardous job. Using pre-wetted carbon eliminates the airborne dust and makes for a clean plant environment.

Processed grades of activated carbon are available that include medical/ pharmaceutical grades, electroplating grades, and powdered or pellet carbons. Activated carbon is a proven technology for the removal of naturally occurring organics and residual disinfectants.

The design of an activated carbon filtration system needs to take into account the differences in the water to be treated, the type of activated carbon used, and the effluent quality and operating parameters.

Download: Here

Sponsored Recommendations

Blower Package Integration

March 20, 2024
See how an integrated blower package can save you time, money, and energy, in a wastewater treatment system. With package integration, you have a completely integrated blower ...

Strut Comparison Chart

March 12, 2024
Conduit support systems are an integral part of construction infrastructure. Compare steel, aluminum and fiberglass strut support systems.

Energy Efficient System Design for WWTPs

Feb. 7, 2024
System splitting with adaptive control reduces electrical, maintenance, and initial investment costs.

Blower Isentropic Efficiency Explained

Feb. 7, 2024
Learn more about isentropic efficiency and specific performance as they relate to blowers.